FEM-2Instruction ManualAs of: 05/2003ALL ARTWORK, PICTURES AND TEXTS ARE COVERED BY OUR COPYRIGHT.THEY MUST NOT BE COPIED (E.G. ON CD-ROM, DISKS OR IN
1011The FEM-2 is compatible with the following cameras and accessories:CamerasARRIFLEX 435 Advanced ...
1011Use of the following equipmentis not permitted Use of the following equipment is not permitted!UC-C2 Run Cable ...
1213Installation and Setup
12134. Setup Switch off the camera and disconnect all cables from the camera and the FEM-2 before installing the FEM-2 on the camera. Switch off the
1415fastening screwguidingsfastening apsInstallation and Setup
14154.1 Installing the FEM-2 on the cameraInstall the FEM-2 on the right side of the camera. Installation must be carried out at an ESD-secured work
1617two screwsM3x8 A2 DIN 912coverInstallation and Setup
16174.2 Installing the URM-1 radio receiver• Untighten the two screws photo and remove the cover.• Remove the two screws (DIN 912 M3*8) from the
1819LDD socketLens motor status LEDDirection selection switchLCS bus socketsCLM-2 plug-in modulefor CLM-2 motorsACC socketCCU LEDURM-1 moduleCCU sock
18195. Operating5.1 Lens Data DisplayThe LDS integrated into the FEM-2 is compatible with all lenses equipped with ARRI LDS contacts.The LDS status L
23Contents
2021URM-1 moduleLDS status LEDRadio status RDY-LEDcannel selectionOperating
20215.2 Radio system Select an RF channel indicated for use in your country before switching on the system.Do not use RF channels that are not permi
2223To change the radio channel:• With the camera off, set the channel and then turn the camera on.• Set the channel selection switch to 9 (deactiva
22235.3 Remote Lens ControlLens MotorsBoth CLM-1 and CLM-2 motors can be used with the FEM-2.• The CLM-1 motors are connected to the LCS bus sockets
2425• Use the direction switch to change the rotational direction of the attached motor.The status LED indicates the following:The following pages sh
CLM-1 IrisZMUFIU FocusLC-F1FIU IrisCLM-1 FocusCLM-1 ZoomLC-F2LC-Z1LC-M1 LC-M2 LC-M22425ZMU-1, FIU-1 and CLM-1 MotorsOperating
CLM-2 IrisZMUFIU FocusLC-F1FIU IrisCLM-2 ZoomCLM-2 FocusLC-F2LC-Z12627ZMU-1, FIU-1 and CLM-2 MotorsOperating
CLM-1 IrisWHA-2CLM-1 FocusCLM-1 ZoomLC-Z1LC-M1 LC-M2 LC-M2WZU-1WFU-12627WFU-1, WZU-1 and WHA-2 mit CLM-1 MotorsOperating
CLM-2 IrisCLM-2 ZoomCLM-2 FocusLC-Z1WHA-2WZU-1WFU-12829WFU-1, WZU-1 and WHA-2 mit CLM-2 MotorsOperating
CLM-1 Focus CLM-1 ZoomLC-Z1LC-M1 LC-M2 LC-Z1CLM-2 IrisZMUWHA-2WFU-12829Mixed OperationOperating
231. ContentsContents1. Contents ...32. Safety Instructions and Legal Disclaimer ..52.1. Safety
CLM-1 Focus CLM-1 ZoomLC-Z1LC-M1 LC-M2CLM-2 IrisZMUWMU-1 WFU-13031Wireless Control of Focus and Iris,Zoom via ZMU-1Operating
CLM-2 IrisCLM-2 ZoomCLM-2 FocusWMU-1 WZU-1 WFU-13031Zoom, Focus and Iris WirelessOperating
CLM-1 Iris CLM-1 FocusCLM-1 ZoomLC-M1 LC-M2 LC-M2WMU-1 WZU-1 WMU-1 WFU-13233Zoom, Focus and Iris Wirelessvia Two Separate Handheld ControlsOperating
32335.4 Camera remote controlNote: For details of how to use the RCU-1 and WRC-1, please see the instruction manuals supplied with these units.For d
WRC-1 + WMU-13435WRC-1 via wireless remote controlOperating
WRC-1 + WHA-2LC-M13435WRC-1 with WHA-2 via cableOperating
WRC-1 + WHA-2WC-W13637WRC-1 with WHA-1Operating
RCU-1KC393637RCU-1Operating
CCU-1KC24S3839CCU-1Operating
38395.5 Time code Check if the area for the time code (barcode) exposure at the edge of the lm is outside of the image area dened by the used form
45Contents5.4 Camera remote control...33WRC-1 via wireless remote control...34WRC-1 with WHA-2 via cable ..
40416. Technical DataOperating temperature ...-20°C to + 50°COperating voltage...As for the ARRIFLEX 435 AdvancedProtecti
40417. Additional DocumentationsInstruction Manual for ARRIFLEX 435 Advanced... K5.58231.0Instruction Manual for the WRC-1 in G
technical data are subject to change without notice© ARRI 2003available languages:Deutsch K5.60901.0English K5.60902.0ARNOLD & RICHTER CINE TECHNI
452. Safety Instructions and Legal Disclaimer2.1. Safety Instructions Please always follow these instructions to help ensure against injury to yourse
67 Do not operate the system in high humidity areas or expose it to water or moisture. Do not place the system on an unstable cart, stand, tripod, b
672.2 DisclaimerNo part of this document may be copied or reproduced in any form or by any means without prior written consent of ARRI. ARRI assumes
89of any material or goods associated with the assembly or use of our products, or any other damages or injury of persons and so on or under any other
893. General DescriptionThe FEM-2 is an expansion module for the ARRIFLEX 435 Advanced camera that provides the following functions:• LDD (Lens Data
Komentáře k této Příručce