ARRI SFHC-1 Specifikace

SXU-1 Single Axis Unit Date: 05 February 2014  Instruction Manual

10 SXU‐1SingleAxisUnit3.3 Control panel 1 Recording button REC 4 Navigation buttons 2 LED for camera status 5 Sensor for AUTO backlight 3

SXU‐1SingleAxisUnit 114 Typical operation setups For both wireless and wired operation, all lens motors must be connected to the camera (or moto

12 SXU‐1SingleAxisUnit 4.2 Wired (via LCS) For wired operation, maximum LCS cable length is 75 m (250 ft). Power is supplied via the camera (or

SXU‐1SingleAxisUnit 135 Power supply 5.1 Rechargeable battery DANGER! High voltage! Risk of electric shock! Use only the recommended battery and

14 SXU‐1SingleAxisUnit5.2 AC power grid DANGER! High voltage! Risk of electric shock! Use only the original AC power pack (see p. 35) and read i

SXU‐1SingleAxisUnit 155.3 LCS hardwire 1. Connect product (1) to camera (2) via a standard LCS cable (maximum length: 75 m/250 ft). 2. Product

16 SXU‐1SingleAxisUnit6 Prior to operation 6.1 Before each switch-on NOTICE: Always prepare the camera first: Connect lens motors and motor con

SXU‐1SingleAxisUnit 17 1. Ensure proper power supply and camera preparation (see p. 16). 2. Press power button (1). 3. Product initializes: Dis

18 SXU‐1SingleAxisUnit 5. CAL blinks CALIBRATING (1). 6. Each connected lens motor moves the lens ring from the end-to-end position. 7. CAL re

SXU‐1SingleAxisUnit 19 4. Submenu opens (C) on preset channel (in this case: 5). 5. Scroll UP or DOWN to select new channel (for frequencies see

2 SXU‐1SingleAxisUnitImprint Copyright © 2014 Arnold & Richter Cine Technik GmbH & Co. Betriebs KG. All rights reserved. No portions of t

20 SXU‐1SingleAxisUnit6.6 Selecting a lens axis 1. Press MENU (A). 2. Menu opens (B). 3. Scroll DOWN until Lens Axis. 4. Press ENTER. 5. Sub

SXU‐1SingleAxisUnit 216.7 Calibrating to lens NOTICE: Each change of lens requires new calibration, including torque and sometimes motor direction

22 SXU‐1SingleAxisUnit6.8 Changing the lens motor torque NOTICE: High torque can damage the lens. Always set a torque appropriate to the lens. R

SXU‐1SingleAxisUnit 236.9 Changing the lens motor direction 1. Press MENU (A). 2. Menu opens (B). 3. Scroll DOWN until Motor Direction. 4. Press

24 SXU‐1SingleAxisUnit7 Operation NOTICE: Conduct all prior-to-operation preparations (see p. 16). 7.1 Changing the backlight The display and c

SXU‐1SingleAxisUnit 25 5. Display opens: here on AUTO (C). 6. Toggle with MODE: here onto FIX (D). 7. Scroll UP or DOWN for backlight intensity (

26 SXU‐1SingleAxisUnit 3. With control knob (C), turn lens axis to desired end position. 4. Press LIMIT (D) again. 5. Blinking changes to an ic

SXU‐1SingleAxisUnit 27 3. With control knob (C), turn lens axis to desired end position. 4. Press K-LIM (D) again 5. Blinking changes to an icon

28 SXU‐1SingleAxisUnit7.5 Switching off 1. Press power button (1) for at least three seconds. 2. Display (2) will count down to zero and go ou

SXU‐1SingleAxisUnit 298 Accessories 8.1 Marking ring Plain white marking rings allow you to scale the control knob with simple board markers. You

SXU‐1SingleAxisUnit 3Contents 1 For your safety 51.1 Risk levels and alert symbols ... 51.2

30 SXU‐1SingleAxisUnit8.3 Optional rigger grip 1. With a 3 mm Allen key, unscrew standard grip (1). Note: Screws are secured from falling into

SXU‐1SingleAxisUnit 319 Maintenance NOTICE: Never attempt to repair the product. Never open it. Never insert objects. Have it always repaired and

32 SXU‐1SingleAxisUnit 8. Press MENU (A). 9. Menu opens (B). 10. Scroll DOWN until Firmware. 11. Press ENTER. 12. Update information appears (C

SXU‐1SingleAxisUnit 33 17. Switch off product. 18. Remove SD card (2). 19. Reattach grip (1). 9.2 System information 1. Press MENU (A). 2. Menu

34 SXU‐1SingleAxisUnit 5. System information appears (C). 6. For menu: Go BACK. 7. Exit via HOME. 10 Storage, shipment, disposal NOTICE: Alwa

SXU‐1SingleAxisUnit 3511 Order numbers K2.0000071 Single Axis Unit SXU-1 11.1 Included accessories K2.72117.0 Plain White Marking Ring K4.0000

36 SXU‐1SingleAxisUnit12 Appendix 12.1 LCS connector pin-out 1 GND 2 NC 3 CAN-L 4 CAN-H 5 Battery +10.4 to 34 V DC 12.2 Dimensions and weight

SXU‐1SingleAxisUnit 3712.4 ARRI white radio channels (ISM B) 0 2.410 GHz 1 2.415 GHz 2 2.430 GHz 3 2.435 GHz 4 2.450 GHz 5 2.455 GHz 6 2.470 GHz

38 SXU‐1SingleAxisUnit12.5 Declarations of conformity EC Declaration of Conformity The product Single Axis Unit SXU-1 conforms with the specifica

SXU‐1SingleAxisUnit 39Canadian Compliance Statement Complies with the Canadian ICES-003 Class A specifications. Cet appareil numérique de la Clas

4 SXU‐1SingleAxisUnit7.3 Limiting the control knob range ... 267.4 Recording ...

 For further assistance ARRI Cine + Video Geräte Gesellschaft m.b.H. Pottendorferstraße 25-27/3/1 A-1120 Vienna Austria E-mail: [email protected] www

SXU‐1SingleAxisUnit 51 For your safety Always keep this document on hand. It should be read, understood and observed by all persons using SXU-1 S

6 SXU‐1SingleAxisUnit1.3 General precautions NOTICE: The product is designed for all cameras with the ARRI Lens Control System LCS or Universal M

SXU‐1SingleAxisUnit 72 Scope of delivery and warranty On delivery, please check if package and content are intact. Never accept a damaged/incompl

8 SXU‐1SingleAxisUnit3 Product layout The SXU-1 is a single-axis hand unit for wireless lens motor control (iris, focus, zoom). It is compatible

SXU‐1SingleAxisUnit 93.1 Product identification Type label and serial number (2) are on the product’s back. FCC ID and IC numbers are on the CE c